46Juliet

2010-03-26T07:47:00.000-07:00

In the left seat of the Spruce Goose. Oh yeah!

2010-03-25T15:49:00.001-07:00

This is my friend Brandy in his Super Cub. Does anybody wonder why we love to fly in the Pacific Northwest?

2010-03-25T15:45:00.000-07:00

This is what she looked like summer of 2009. Yep! That is yers truly. Over the winter I have removed the wheel pants. They look nice (when clean) but are a royal pain.

2010-03-25T15:44:00.001-07:00

I haven't paid much attention to this blog since the airplane went back into the air. But I thought I would add a few items from time to time.

Grand Finale

2009-02-23T20:30:00.001-08:00

November 8346 Juliet returned to the air today!

The first start. It all checked out!

The cowl is on.

Taxi-ing out to the fuel pumps.

Taxi-ing out to Runway 23.

departing 23.

Gotta love that climb prop!!

On approach to 23.

On final.

On short final.

On REALLY short final.

The flair!

Engine

2009-02-23T08:40:00.000-08:00

Here is the engine, freshly arrived and ready to hang on the airplane.

Mechanic extradinaire Dennis Toepke hard at work. The engine is attached to the airplane and the prop has been mounted. The prop will need to come off. We discovered that the mounting plate for the spinner is cracked.

The interior is finished!

Progress

2009-02-16T15:52:00.001-08:00

A lot has been done, but not much for photos. The majority of the carpet is finished, all except the right kick panel. It will get done this week. One seat is upholstered (see previous) and the left seat is left to do. It also must get done this week.

I invented a reasonable Push-to-Talk switch. The previous one was velcro-ed on and would not stay put. The above photo shows my invention. It is a standard cable clamp with a momentary contact switch bolting the thing to the yoke. It isn't much different than the previous one, except that its stays put.

The engine arrives on the 21st and everything should be complete, and the airplane airworthy, by the 22nd.

Seats

2009-02-11T14:27:00.000-08:00

Here is the right seat, re-upholstered and ready to be installed. The seats won't go back in until after the engine is installed. Juliet is due for an annual inspection, which we will do while installing the engine. The seats need to be out for that.

Carpet

2009-02-11T14:24:00.000-08:00

The new carpet is almost completely installed. The kick panels need to be done and installed and that project is over. Also note the the cleaned and repainted door panels are installed. The problem with the door panels is that they accentuate the ugly yellow door posts and other interior metal. The only cure would have been to completely strip out the interior and paint everything. That was too big a project this time around.

Just for grins

2009-01-24T17:43:00.000-08:00

In case you ever wondered what a Cessna 150 looked like without an engine.

Excitement!!!

2009-01-24T17:35:00.000-08:00

The panel is finished. Well almost. A few minor details and touchup. And actuall, the center stack overlay is a "final trial fit". Which is synomous with "I just gotta see what this is gonna look like!!!".

Panels

2009-01-22T08:16:00.000-08:00

Here are before and after photos of the plastic door panels. The difference is stunning. I used Kryl0n's Fusion spray paint.

Progress

2009-01-20T10:00:00.000-08:00

Last evening I pulled all of the interior plastic trim. It involved a little contortion. Great care must be exercised because the stuff is pretty flimsy. It will get painted this evening.

I also got the old, very ugly, carpet out. In terms of reassembly, the new yoke bushings are in. Once the left yoke is back, I will be ready to re-assemble the left panel and the avionics fillers.

The new seats and carpet arrived from Tnwings this morning. They look wonderful. Installation will start forthwith!

Photos

2009-01-14T08:25:00.001-08:00

Here are photos of the right side overlay, INSTALLED! The upper avionics filler overlay is also in place. I think the tail number on the overlay came out pretty well. Last evening I got the right yoke installed, so the right side is finished. Yes, the acorn nuts will get touched up with black paint.

I need to get the Nikon up to the hangar.

Big Progress

2009-01-13T14:58:00.000-08:00

The right side overlay is IN!! I will take photos when the whole panel is in place. But the right side overlay looks good. Though I need to take some Armor All to the lower panel.

The friend who was preparing the left yoke for a PTT has run into difficulties. I may go a different route. A company makes very nice leather covers with a built-in PTT. They are very proud of 'em though.

I just received a phone call from Shelby Isham at Tnwings. The new seats and carpet should be on its way tomorrow. I am very excited about that.

Real Progress

2009-01-10T16:00:00.001-08:00

Here are a couple of photos of the completed panel overlays. I had to take two photos because I couldn't get far enough away in my basement to get everything in. These are now ready for installation. The right panel overlay will probably go in in the next few days. The left panel and the avionics stack fillers will have to wait until the left yoke is back in my hands.

In case anyone was in doubt as to the ugliness of the seats, here is a good photo. New upholstery, to be installed along with new cushions on the original frames, is on the way from Tnwings.

In addition, the propeller is now in my hands. It looks very nice. We will see how if performs. I finally made progress on baffles seals. They are about 2/3's done. I would have completed them today but my hands got too cold. It is not balmy in the hangar!!

Small Steps

2009-01-07T08:45:00.000-08:00

The panel overlays are complete and ready to re-install. I don't have photos at the moment, but will add them soon. Installation will need to wait until I get the left yoke back. It is in Georgia being set up for a new PTT. The instant that yoke arrives back panel re-assembly starts and that job will be complete.

The overhauled and re-pitched propeller arrived yesterday. I am excited about that. I also received word that the engine will be complete by the end of the week. But there is much to do before it is ready to hang.

I started the task of preparing the new starter push button for installation. So far I have removed the old pull starter and am working on ways and means of enlarging the hole in the panel. It should be easy, but is turning into a bit of a project.

New Years Day

2009-01-01T17:04:00.000-08:00

Baby steps are being taken. A friend is helping arrange a PTT for the left yoke. But it involves shipping the yoke off to him. I got that prepared today. MAN, was it cold in the hangar. I was thinking of doing the prep work necessary for the new starter push button, but it was just too cold to work there today.

I also re-painted the right side overlay. But it still isn't good. I think I will strip it back to bare metal and start over.

Once I get the panel and overlays painted to my satisfaction I will post photos.

Seats

2008-12-31T08:55:00.001-08:00

Progress has been slowed by the holidays and the lousy weather. But I did get in a call to Shelby Isham at Tnwings yesterday. We had a pleasant conversation. The new upholstery and carpet has been ordered and should be on its way here sometime next week.

I am still battling paint issues on the overlays, specifically, the right side overlay. I sanded down the orange peel and re-painted. However, I didn't really get the paint properly feathered and will need to re-do, again. Which is OK, because it orange-peeled ... again. I gotta figure out why.

Christmas Report

2008-12-25T13:47:00.000-08:00

Progress has been slowed by family events, work and the weather. I have been working on the dry transfer lettering on the overlays. The process is fussy and difficult with a steep learning curve. I am closing in on it and hope to have the overlays completed tomorrow, but we shall see.

The weather here in the Pacific Northwest has been frightful. I understand that some New England folks may not think of 20" of snow as much of a big deal. But we are not used to it. Snow "storms" around here usually dump 3-6" and hang around for a couple of days. This series of storms has blanketed the area with 15-24" and has lasted a couple of weeks.

I went up to the airport a couple of days ago. I had too. I had hidden my wife's Christmas present in the hangar (it seemed a good idea at the time). The snow was knee deep between the hangars and was blown up against the doors. For a bit I wasn't sure I would be able to get the hangar doors open. Getting there had been a chore as well. The access gate was inoperative, so I had to enter at the FBO and slog through the snow to the hangar. Fortunately, the main taxi-ways have been plowed, which cut down on the slog, but gave me the opportunity to fall on my butt!

Prop

2008-12-19T08:54:00.000-08:00

I received a call from the propeller folks. There were no major issues. The prop is on its way back overhauled, repitched and painted.

The dry transfer process I am using for the lettering on the overlays is proving to be a bit involved. However, I woke up at 0130 this morning with a flash of brilliance that explains my difficulties.

PROGRESS

2008-12-18T07:50:00.000-08:00

A few things have been accomplished since December 10. First, on December 12, the propeller went to Aircraft Propeller Repair Services in Troutdale, Oregon. It was a miserable day and I couldn't find anyone who wanted to fly down, so I drove it down there. The gracious folks there took an initial look at the prop. They were concerned about some corrosion in the hub area. I haven't heard from them yet, which gives me hope that the corrosion turns out to be a non-issue. They will overhaul the prop and re-pitch to 46" from the current 50".

The re-pitch will mean I will no longer have the fastest 150 on the block. With the 50" prop Juliet would cruise at 118 mph at 2500 rpm. After burning off a bit of fuel, I often had to throttle back to 2450 to stay below the yellow arc on the airspeed indicator. But climb performance was nothing short of miserable. Since almost all of my flying is over short distances, and I favor the smaller airfields, the improved climb performance will be very welcome, and I don't think I will miss the higher cruise speeds. I hope it will also mean I can climb out of Sanderson on a warm (not hot) day with two people and full fuel aboard.

During the return trip I learned that my very good friend, Hollister Young, had passed away. It was difficult to weep and drive at the same time. I pulled over and composed myself before continuing my trip home. I spent quite a few pleasant hours with Holly in his Cessna 185, which is the first airplane I ever flew. Holly was a terrific gentleman, and a good, and close, friend.

Panel work has progressed, as well. The left side floating panel and all of the overlays have been painted. I am not as happy as I might be with the paint, but I am running out of time. So it will have to do. During some succeeding winter I will probably pull things apart and re-do the panels ... again. At least I won't be distracted by all the other tasks I am currently undertaking.

You may recall I was originally going to have printed overlays done by PlacardsPlus. The decision to forgoe re-doing the lower panel (in retrospect, a wise decision) drastically reduced the amount of lettering necessary. I can handle the remaining lettering with a dry transfer process.

Once the lettering is complete I will overspray the panel and overlays with a clear, flat protective coat. Today will see the various screws and nuts associated with the panel and overlays painted and all of that will be ready to go back together.

The steel engine parts are on their way back to Dennis Toepke, along with the necessary bearings, gaskets, seals and new nut/bolt kits. I haven't heard back from the folks going over the case, except it is out of the welding shop. Which means (a) it needed some welding, and (b) progress is being made.

There is a lot of work to be done before the airplane will be back in the air. The baffling needs to be stripped and re-painted and the new seals installed. I haven't even ordered the new upholstery and carpet yet, nor have I started work on the interior trim plastic. Holiday activities have slowed me down some, but I need to keep rolling so the rest of the airplane will be ready when the overhauled engine arrives. Dennis hopes the engine will be ready to hang before the end of the year. Which means I need to break free from the computer and do something useful!

2008-12-10T08:16:00.000-08:00

The right side overlay is finished. Sort of. As I was thinking about it last night, I was not as happy with it as I might be. The opening for the ammeter is off by about 3/16" horizontally and vertically. The opening for the tach is off by about 1/16" vertically. The opening for the fuel and oil gauges could be about 3/16" larger vertically. So early this morning I was thinking I might abandon this idea and return to the stock Cessna plastic overlays. Looking at this photo now, I am inclined to continue with the aluminum overlay.

Even if I go back to the plastic overlays, I will not completely abandon this project. I could make a new right side overlay. There is only about $5 worth of aluminum here. But I am running out of time.

After I took this photo I removed the left side panel. All of the shock mounts are shot. Even if I decide to abandon the new overlay scheme, this disassembly has had value. Obviously, the shock mounts need to be replaced. I am also replacing the yoke grommets, which were seriously worn.

The changes to the filler overlays in the avionics stack are an unmitigated success. Those overlays are a very large improvement over what was there.

2008-12-03T14:36:00.000-08:00

The template for the right side overlay is completed to my satisfaction. Finally. This has been a time-consuming and fussy job. The next step is to use this template to actually fabricate the aluminum overlay.

Friday Progress

2008-11-28T17:58:00.000-08:00

OK friends and neighbors, here are the basic components in the mount for the Bendix/King AV80R GPS. The aluminum is the overlay that fits just below the transponder. Right above it is the holder for the GPS provided in the box. To the right are the fasterners, a 6-32 x 1/2" screw, a #6 washer, a #6 lockwasher, another #6 washer and a #6 nut.

The screw goes through the slot in the holder with a washer behind it to spread out the forces. The slot is exactly the width of a #6 screw, so I had to take a small file and widen the slot just a smidgen.

This is the back side. Washer, lock washer, nut. Nothin' to it!

And here is the trial fit. I think it is going to be pretty snazzy, once the panels are all painted a dark gray and everything is back together.

Right Side Panel

2008-11-26T16:14:00.001-08:00

I just received word from my mechanic that the FAA is not doing field approvals at the moment. So, it is back to the original idea of a new cosmetic overlay on the right side panel.

Progress

2008-11-26T09:24:00.000-08:00

Progress has been a little slow. I have had some projects around the castle that have needed my attention, coupled with a couple of bouts of laziness.

But I have tested the proposed location for the AV80R. It fits, and will look, great. Sorry, no pictures. I couldn't hold the unit with both hands and work the camera at the same time.

Work has started on replacing the baffle seals. As you can see from the above photo, the seals were well past the point of needing replacement. They appear to be the original seals. Which is too old by more than a few years.

This is the seal kit that I ordered from Aircraft Spruce. It appears to be good quality material and the price was very reasonable. The kit includes the seals, two packages of rivets (it looks like way more than enough), washers, and a package of screws and nuts that I haven't figured out yet. Note that they even include an appropriately sized drill bit.

I worked on removing the old seals last night. It is fussy work drilling out the old rivets and pulling the old staples (yes, the factory STAPLED some of the seals in place). I worked until the battery on the drill gave out. I got about 2/3's of the rivets out.

A good deal of care is in order as the baffles are very light gauge aluminum and can be easily damaged.

I also got educated on the differences between "old design" and "new design" drive couplings for the alternator. I purchased a new drive coupling from Quality Aircraft Accessories. Who are, by the way, great folks with which to work. Those little puppies are $574 each with a $500 core charge. The bad news is that the "old design" coupling is not an acceptable core. It turns out that if the old design coupling fails, it tends to spread bits and pieces throughout the engine. So having the new design is a good thing. But $1,074 for that small part is more than slightly painful.

Panel Update

2008-11-19T09:30:00.000-08:00

The fabrication of the new overlay for the right side panel is on hold. A couple of friends in the 150/152 club suggested that I fabricate a floating panel for the right side instead of just doing a new overlay.

This constitutes more than a cosmetic change. So, my mechanic is checking with the FAA on the possibility of doing a field approval.

Engine News

2008-11-17T09:15:00.000-08:00

The mechanic has gotten the engine completely disassembled. I didn't need to worry about that one cylinder flange nut, or the stud or case. I broke one of the through-bolts. All of the studs, nuts and bolts get replaced anyway, so no harm done.

The case and the steel parts have been shipped off for inspection. The case will probably get line bored, in addition to new studs. We will see if the cam and/or crank need to be ground.

Overlay Progress

2008-11-17T08:30:00.000-08:00

The first trial fit for the right side overlay template is to make sure the mounting holes line up. If you look closely, you can see the layout lines for the round openings. The next step is to cut out the round openings and make sure they line up with the instruments. Once I am sure they are in the right places, I will cut the openings for the fuel and oil gauges.

The center stack overlays fit perfectly! The blank area below the transponder will host the Bendix/King AV80R GPS.

The center stack overlays have been drilled and are ready for a trial fit. The right panel overlay template has been cut out and the mounting hole locations drilled.

You have to view these images from bottom to top. It is just the way the blog is set up. This is the panel as it looked Saturday morning.

These are the overlay blanks ready for layout and drilling. The large one on the left is for the right side panel. The middle one fits below the transponder in the center stack, and the small one goes on top of the radio.

Engine

2008-11-12T18:36:00.000-08:00

The engine is in the hands of the mechanic. We (my Wife and I) hauled it up to Port Angeles on Saturday. It looks like a solid month before it will be ready to hang.

I have started pulling out cabin items. The instrument panel is pretty much disassembled, the seats are out, and I am about to pull out the ugly carpeting. But first, I will be fabricating a new overlay for the right side of the instrument panel.

The left side is easy. I will simply install new overlays on the existing, floating, instrument panel. But Cessna, for whatever reason, mounted all the right side instruments directly on the sub-panel, which is a structural part of the airplane. So, a new overlay is in order if the right side is to match the left side.

What fun!

Progess

2008-11-03T08:38:00.000-08:00

I started work on removing the remaining three cylinders this past Saturday. I have had real problems with recalcitrant nuts.

I was hauling on one of the #2 cylinder flange nuts, and it seemed to break loose. Not so. I observed that the stud was turning, and not backing out. I couldn't pull it out either. This is not good.

The decision was made to leave the removal of the rest of the cylinders to the professional. I just may have caused myself more trouble than I bargained for. I will know for sure once the mechanic gets that cylinder off and lets me know if the damage I did is beyond repair ( $$$$ :( ).

I had a very positive experience with Aircraft Spruce last week. I got confused in ordering the spark plugs and ignition harness on-line, so I called. Mike was very helpful in guiding me through what I needed.

This evening will be spent cleaning parts, which I hate. But I hate paying a professional mechanic to do it even more. Sometime this week the intake tubes and the oil tank will get painted and everything will be ready to go up to the mechanic in Port Angeles. That is scheduled for next Saturday.

MAGNETOS

2008-10-28T08:46:00.000-07:00

Aircraft Magneto Services in Seattle received my mags yesterday. They found them suitable for the 500-hour service, which they completed. They are shipping them back to me today. The price was reasonable, too.

That kind of service is a thing call "customer service", and these folks know all about it.

Weekend Progress

2008-10-27T10:28:00.000-07:00

Things are moving along. All of the accessories are off (photos to follow), the vacuum pump is off, the intake system has been removed, as well as the exhaust system, and the oil tank is draining in a bucket.

I have also gotten one cylinder off. Peering in the crankcase, things look pretty good. I don't see any signs of corrosion and there doesn't appear to be any pitting on the cam. I am crossing my fingers because the condition of the bottom end of the engine will have a major impact on the overall cost of the overhaul.

I had considerable help over the weekend. My buddy Dean showed up on Saturday and spent a good deal of time fetching wrenches, holding parts and asking lots of questions about aircraft engines. I enjoyed the company. On Sunday (yes, I skipped morning church) my hangar neighbor Brandon came over and helped get the oil tank off. Again, I enjoyed the company. The hangar can get kinda lonely sometimes.

There is a pause in parts ordering as I am changing banks. My aviation account has been at the same bank for quite some few years. I made the mistake of not completely understanding the bank's policy regarding out of character purchases. The bank made the mistake of offering something less than stellar customer service in the process of straightening it out. I am stuck with one foot on the boat and the other on the dock until the card comes from the new bank.

Magnetos

2008-10-23T15:57:00.000-07:00

I have learned a lot about Slick magnetos in the last couple of days. My hat goes off to Cliff at Aircraft Magneto Services. These folks are wonderful.

Of major importance is a word about low priced "exchange" Slick magnetos. "Exchange" Slicks are not overhauled, they are new. It is not cost-effective to overhaul the Slick mags. There was an AD issued recently on some Slick mags. If you are ordering exchange mags, be certain that the serial numbers are above 0808453.

If the price seems to be too good to be true, it probably is and you will need to deal with a rather inconvenient AD.

My mags are going off to Magneto Services, Inc. tomorrow for evaluation. Basically, if the impulse coupling is good, the mag is a good candidate for the 500-hour service. If not, then I will be shopping for new mags.

You can call Cliff at 206-768-3099. The company is located on Boeing Field (King County Airport) in Seattle.

2008-10-21T09:18:00.000-07:00

The project is off to a flying (no pun intended) start. The magnetos and the carb have been removed, along with many small bits and pieces.

The next step is to ship the mags and carb off for overhaul.

A lot of parts have been ordered. I want to express my thanks to Chief Aviation in Grants Pass, OR., A.E.R.O., and Aircraft Spruce. These are great companies from whom I have received excellent customer service.

Before

2008-10-19T15:32:00.001-07:00

The following are the "before" photos. Just minutes before I started pulling things off the airplane. You can note that she is a pretty little bird. I like to say that she has a good "10-foot" paint job. It looks great from 10 feet. No exterior changes are contemplated, though I may remove the wheel pants. They look good, but they are a pain in the neck.

As you can see, the plastic is in pretty good shape, though dirty and discolored. That will be fixed. You can also get a glimpse of the really ugly, and uncomfortable, seats. Shelby Isham at Tnwings will be helping with that.
Again, the plastic is solid. Shelby will be helping with the ugly (and probably not acceptable to the FAA) carpet
I have always liked the "G" model panel. It is reasonably simple, pretty well laid out, and pre-dates Cessna's need to "color coordinate". The color matched lower panels of later models can look really hideous. Especially on colors like yellow. The yokes are in good shape. I had thought of getting leather yoke covers, but they don't need it. The push-to-talk switch arrangement will be getting fixed.

I am going to retain Placards Plus to do new overlays for the panel. This will eliminate the Cessna plastic overlays and the panel will resemble the newer Cessna panels that do not have the plastic overlays. I am also going to slightly modify the lower middle panel by lowering the intercom to align it with the avionics master switch and the radio's circuit breakers. That will leave a space to mount the Bendix/King AV80R I have on order.

This piece of ugly carpet is loose. Shelby's new carpet will fix that. Interior colors will be gray. It is easy on the eyes. If the budget allows, the throttle and mixture controls will be replaced with the more modern type.